2944.26 Per Piece | Discount | |||||||||
|
|
You Save |
![]() |
![]() |
![]() |
![]() |
Zycosil Plus
Zycosil Plus is a water soluble penetrative solution for waterproofing of masonry building material. Zycosil is Nano technology based as it provides molecular level hydrophobicity to inorganic substrate and it is eco-friendly as it is applied in water solution. The product is based on organosilicon chemistry, hence reacts with the inorganic substrate surface, seals the surface uto a depth of 2-3 mm and provides long service life. The Nano size allows penetration deep into substrate that provides 20+ years water repellency. This product is very economical. Zycosil is 10-20 % of the cost of solvent based silane technology. Zycosil and its diluted solution are non flammable and easy to apply using paint brush, roller or airless spray. No special tools or precautions are necessary to handle the product. It is ideal for making the roof and walls water repellent.
Additional Information
100% Silane
Water soluble nanotechnology
Life: 20+ years
Penetrative in very fine pores and cracks
Reactive, non leachable
UV & Heat stable
Abrasion resistant
Does not break like a surface film
Gives long lasting protection
ZycoPrime+
ZycoPrime+ is an Acylic co-polymer emulsion, supplied as a ready to use bonding agent in liquid consistency. It is a versatile product and can be used as a cement modifier for repair of spalled concrete - slabs, balconies, beams, columns, floors & waterproofing of toilets, bathrooms and terraces.
FEATURES & BENEFITS
APPLICATION AREAS
APPLICATION METHOD
Clean the surface with wire brush, scrubber or air blower to remove hidden dirt, loose particles, laitance & dust. De-grease the surface by using suitable solvents, if needed.
To be used as a clear bonding primer by diluting 1:5 with water. Apply on the walls before painting or during putty rendering.
For priming of concrete substrate, the surface should be thoroughly saturated with ZycoSil+ solution (Dilution Ratio - 1 part ZycoSil+ : 20 parts potable Water : 2 parts of ZycoPrime+).
For a waterproofing coating mix 1 part ZycoPrime+ with 1 part of cement & 1 part of 100 mesh sand. Add water for brushability. Brush apply the mix in span of 4-6 hours on the prepared concrete substrate. It is recommended to saturate the surface with ZycoSil+ solution prior to this application. Overlay the coating with a protective screed to the desired slope and thickness. Coverage : 4-5 m² for a 0.2 mm (200 microns) coat.
Repair Mortar & Renders, Floor Screed & PCC
Prepare the Mortar in the following proportion: Cement 50 kg Washed Sand 75 kg 6 mm Down size aggregates 75 kg ZycoPrime+ 6-7.5 litres Water 10 litres For PCC & Plaster work : ZycoPrime+ 100 ml per bag cement (conforms to IS 2645 - 2003)
APPLICATION DETAIL
Sr. No. |
Application |
Recipe |
Zycoprime + Qty. |
1 |
Patching & Repair Mortar |
Portland Cement : 50 kg Washed Sand : 10 KG Water : 10 ltrs |
6 - 7.5 ltrs |
2 |
PCC / Plaster |
Portland Cement : 50 kg |
100 ml |
3 |
Waterproofing membrane (rough) |
Portland Cement : 1 kg |
1 ltr |
4 |
Putty |
Putty - 20 kg |
100 ml |
5 |
Waterproofing Primer |
ZycoSil+ solution (1:20) |
2 ltr |
6 |
Bonding Primer |
5 ltrs water |
1 lt |
7 |
Coving |
ZycoPrime+: 1 ltr Water : 2.5 ltr Cement : 5 kg Sand : 15 kg |
Mix manually / mechanically Use the mixture for smooth coving |
Zycoprime Plus is 100% acrylic co-polymer emulsion, which is used as a bonding agent for excellent adhesion of the concrete mixture on Zycosil treated surfaces (plaster/slab).
Additional Information
Zycosil Plus
Zycosil Plus is a water soluble penetrative solution for waterproofing of masonry building material. Zycosil is Nano technology based as it provides molecular level hydrophobicity to inorganic substrate and it is eco-friendly as it is applied in water solution. The product is based on organosilicon chemistry, hence reacts with the inorganic substrate surface, seals the surface uto a depth of 2-3 mm and provides long service life. The Nano size allows penetration deep into substrate that provides 20+ years water repellency. This product is very economical. Zycosil is 10-20 % of the cost of solvent based silane technology. Zycosil and its diluted solution are non flammable and easy to apply using paint brush, roller or airless spray. No special tools or precautions are necessary to handle the product. It is ideal for making the roof and walls water repellent.
Additional Information
100% Silane
Water soluble nanotechnology
Life: 20+ years
Penetrative in very fine pores and cracks
Reactive, non leachable
UV & Heat stable
Abrasion resistant
Does not break like a surface film
Gives long lasting protection
ZycoPrime+
ZycoPrime+ is an Acylic co-polymer emulsion, supplied as a ready to use bonding agent in liquid consistency. It is a versatile product and can be used as a cement modifier for repair of spalled concrete - slabs, balconies, beams, columns, floors & waterproofing of toilets, bathrooms and terraces.
FEATURES & BENEFITS
APPLICATION AREAS
APPLICATION METHOD
Clean the surface with wire brush, scrubber or air blower to remove hidden dirt, loose particles, laitance & dust. De-grease the surface by using suitable solvents, if needed.
To be used as a clear bonding primer by diluting 1:5 with water. Apply on the walls before painting or during putty rendering.
For priming of concrete substrate, the surface should be thoroughly saturated with ZycoSil+ solution (Dilution Ratio - 1 part ZycoSil+ : 20 parts potable Water : 2 parts of ZycoPrime+).
For a waterproofing coating mix 1 part ZycoPrime+ with 1 part of cement & 1 part of 100 mesh sand. Add water for brushability. Brush apply the mix in span of 4-6 hours on the prepared concrete substrate. It is recommended to saturate the surface with ZycoSil+ solution prior to this application. Overlay the coating with a protective screed to the desired slope and thickness. Coverage : 4-5 m² for a 0.2 mm (200 microns) coat.
Repair Mortar & Renders, Floor Screed & PCC
Prepare the Mortar in the following proportion: Cement 50 kg Washed Sand 75 kg 6 mm Down size aggregates 75 kg ZycoPrime+ 6-7.5 litres Water 10 litres For PCC & Plaster work : ZycoPrime+ 100 ml per bag cement (conforms to IS 2645 - 2003)
APPLICATION DETAIL
Sr. No. |
Application |
Recipe |
Zycoprime + Qty. |
1 |
Patching & Repair Mortar |
Portland Cement : 50 kg Washed Sand : 10 KG Water : 10 ltrs |
6 - 7.5 ltrs |
2 |
PCC / Plaster |
Portland Cement : 50 kg |
100 ml |
3 |
Waterproofing membrane (rough) |
Portland Cement : 1 kg |
1 ltr |
4 |
Putty |
Putty - 20 kg |
100 ml |
5 |
Waterproofing Primer |
ZycoSil+ solution (1:20) |
2 ltr |
6 |
Bonding Primer |
5 ltrs water |
1 lt |
7 |
Coving |
ZycoPrime+: 1 ltr Water : 2.5 ltr Cement : 5 kg Sand : 15 kg |
Mix manually / mechanically Use the mixture for smooth coving |
Zycoprime Plus is 100% acrylic co-polymer emulsion, which is used as a bonding agent for excellent adhesion of the concrete mixture on Zycosil treated surfaces (plaster/slab).
Additional Information
© 2018-2022 ApnaGharBanao
Last Update : 09-04-2022 | Version : 2.1.6